Huis> Product List> Horizontale slurrypomp> ZJW-voedingspompen> Molen Slijpen Voedingspompen
Molen Slijpen Voedingspompen
Molen Slijpen Voedingspompen
Molen Slijpen Voedingspompen
Molen Slijpen Voedingspompen
Molen Slijpen Voedingspompen
Molen Slijpen Voedingspompen

Molen Slijpen Voedingspompen

$5000≥1Set/Sets

betaling Type:L/C,T/T,Paypal,Money Gram,Western Union
Incoterm:FOB,CFR,CIF,EXW,FAS,FCA,CPT,CIP,Express Delivery
Min. orde:1 Set/Sets
vervoer:Ocean,Land,Air,Express,Express
Haven:Tianjin,Qingdao,Guangzhou
Productkenmerken

Model65ZJW

merkNaipu

TypeClay Wet Sand

Casting MethodThermal Gravity Casting

Sand Core TypeClay Sand Core

ApplicationMachinery Parts

MachiningBoring Machine

MaterialSteel

Surface TreatmentSand Blast

Surface RoughnessRa0.4

StandardGB

CertificationISO 9001:2008

65ZJW Feeding Pumps65

Verpakking & Levering
Verkoopeenheden : Set/Sets
Pakkettype : Houten doos
Afbeeldingsvoorbeeld :
Beschrijving

65 zjw Filterpers Voederpompen

Vrijdragende horizontale centrifugale drijfmestpompen/met rubber beklede drijfmestpompen/R55 drijfmestpompen/pakkingsdrijfmestpompen/centrifugaalafdichtingen drijfmestpompen/slijtvaste rubberen drijfmestpompen/ verwisselbare drijfmestpompen/Kolenwas drijfmestpompen/Zand en grind behandeling drijfmest pompen/Afvalverwerkingsdrijfmest pompen / pompen voor flotatie van mineralen / pompen voor het wassen van kolen / voedingspompen


Naipu® NP-ZJW- serie filterpersvoedingspomp accepteert unieke hydraulische desin en installatiemodus van de

waaier, zorg ervoor dat de prestatiecurve van de pomp steiler is dan normale pompen, is meer geschikt om te gebruiken in de

filterperstoevoer varieert afhankelijk van de veranderingen van de weerstand om de grote capaciteit te realiseren,

lagedruktoevoer en lage capaciteit, hogedrukfilter. De pomp wordt veel gebruikt in de kolenwasserij,

milieubescherming, aluminium fabriek, smelterij etc.



Bouwtekening

drawing-1





De structuurgrafiek van de voedingspomp:

1. Tweefasige slakkenhuis 2. Tweefasige waaier

3.Eenfasige slakkenhuis 4. Achterplaat:

5.Voedingsruimte 6.Locatiestruik:

7.Expeller 8.Expeller afdekplaat

9.Decompressielichaam 10.Eenfasige waaier:

11.Tie-bar 12.Shaft sleeve

13. Afdekplaat 14. Demontagering

15. Waterhoudende plaat 16. Lager:

17.Shaft 18.Bearing spacer sleeve

19.Lagerdeksel 20.Frame

21.Gebogen pijp



NP-ZJW POMP SELECTIEKAART:

selection chart



NP-ZJW VOEDINGSPOMP PRESTATIEPARAMETERS

Performance Parameters


Productoverzichten:

Filter Press Photos


Mogelijke fouten en schikkingen.


        Faults

    Reason

      Settlement

1.Pump fails to discharge any water,The hand of pressure gauge beat violently

1.Suction pipe don`t have enough water.

2.Suction pipe blocked or the valve is locked.

1. Inject enough water

2.unlock the inlet valve,clear the blocks

3.Exclude the air leakage

2.The pump can`t discharge water,the hand of vacuum meter beat heavily.

1.The inlet valve is unlocked or silted up.

2.The resistance of suction pipe is too big or silted up.

3.The height of suction is too high.

1.Unlock the valve or desilting

2.improve the design of  suction pipe or desilt

3.Lower the height of the installation.

3.The pump can`t discharge water,pressure gauge shows heavy pressure.

1.The resistance of the discharge pipe is too big.

2.The impeller blocked

3.The speed is slow.

1.Check and adjust the outlet pipe.

2.Clear the impeller

3. Improve the speed.

4.The pump doesn`t rotate

The volute is silted up by the blocks.

Clear the blocks

5.The capacity is not enough

1.The blocks of the impeller or the inlet or outlet pipe.

2.The abrasion of the impeller is heavily.

3.The speed is low to normal

4.Pump is installed unreasonably or the leakage of the inlet pipe.

5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.

6.The inlet valve not open enough or blocked

7.The packing seal leaks

1.Clear the impeller or pipe.

2.Change the impeller

 

 

3.Adjust the speed

4.Install again or stop leaking.

 

 

5.Decrease the height of the transport or reduce the resistance.

6.Unlock the inlet valve

 

7.Compress the packing tightly

6.The motor of the pump is overloaded

1.The head of the pump exceeds the head of the working condition.

2.Not consider the slurry density when selecting the pump.

3.The packing press tightly

1.Turn down the outlet valve,cut the impeller or lower the speed.

2.Select the motor again.

3.Adjust the the screw of the  packing gland

7.Abnormal sound in the pump, and no water out

1.The resistance of the inlet pipe is too big.

2.The height of the suction is too high.

3.Cavitation occurred

4.there is air in the inlet

5.The temperature of the liquid is too high

1.Clear the suction pipe and sluice valve.

2.Lower the height of the suction

3.Adjust the water valve and let the pump operate in the defined limits.

4.Block the leakage.

5.Lowering the liquid temperature.

8.pump vibrates

1.pump cavitate

2.The block of the impeller single vane

3.The no concentricity  between the pump shaft and motor shaft

4.Fasteners or foundation loose

1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.

2.Clear the impeller

3.Alignment again

4.Fasten the screw,and reinforce the foundation.

9.Bearing is overheat

1.lock the cooling water

2.lubrication is not good.

3.the lubrication oil is not clear

4.the wrong direction of the thrust bearing.

5.there is something wrong with the bearing.

1.Open the cooling water

2.Adjust the oil quantity

3.Clear the shaft,change oil

4.According to the inlet pressure,adjust the direction of the thrust bearing.

5.Change the bearing

10.Packing short life

The material of packing is not good

Change the packing

11.pump leak oil

1.High oil level

2.The rubber parts invalid  

3.Assembly problem

1.Lower the oil level

2.Change rubber spares

3.Adjust the assembly

 

12 Pump head leaking

1.The rubber parts not press well

Assembly again or press tightly 





FAQ:

Q1. Bent u een fabrikantfabriek?

Ja, wij zijn de directe fabricagefabriek en hebben meer dan 10 jaar ervaring op dit gebied.

Q2.Heeft u voorraadproducten om te verkopen?

Sommige hebben we op voorraad, andere niet. Omdat we deze producten altijd volgens de wensen van de klant produceren.

Q3.Welke voordelen heeft u?

A: Wij zijn een directe fabrikant en de prijs is concurrerend.

B: Onze ingenieur is zeer ervaren op dit gebied en we kunnen OEM-service aan u verlenen.

C: We zijn in de fabriek en we kunnen het productieschema regelen, om stipte levering te garanderen.


Contact details:

Shijiazhuang Naipu Pomp Co., Ltd.

Toevoegen: No.368 Xinshi North Road, Shijiazhuang Hi-Tech Industry Development Zone, Hebei, China, 050091.

Tel: 0086-311-897162903

Fax: 0086-311-87162902

Contactpersoon: Karen Tan

Skype: karen_naipump











Huis> Product List> Horizontale slurrypomp> ZJW-voedingspompen> Molen Slijpen Voedingspompen
  • Klik Hier om onderzoek te sturen

Copyright © 2024 Shijiazhuang Naipu Pump Co., Ltd. Alle rechten voorbehouden

Klik Hier om onderzoek te sturen
*
*

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

verzenden